![]() ![]() When powered by DC or 802.3at (class 4) PoE, the AP will operate without restrictions units.Power sources are sold separately see the 500 Series Ordering Guide for details.When both DC and PoE power sources are available, DC power takes priority over PoE units.The AP supports direct DC power and Power over Ethernet.Security slot: Kensington security slot.Serial console interface: Proprietary, micro-B USB physical jack.Reset button: Factory reset, LED mode control (normal/off).Visual indicators (two multi-color LEDs): For System and Radio status.Zigbee: up to 6dBm transmit power and -96dBm receive sensitivity Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.3dBi.BLE: up to 7dBm transmit power (class 1) and -93dBm receive sensitivity (1Mbps).Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio:.USB 2.0 host interface (Type A connector): Capable of sourcing up to 1A / 5W to an attached device.DC power interface: 12Vdc (nominal, +/- 5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length.802.3az Energy Efficient Ethernet (EEE).PoE-PD: 48Vdc (nominal) 802.3af/at PoE (class 3 or 4).Auto-sensing link speed (10/100/1000BASE-T) and MDI/MDX.E0: Ethernet wired network port (RJ-45):.Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 4.3dBi in 2.4GHz and 5.6dBi in 5GHz.The downtilt angle for maximum gain is roughly 30 degrees. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. Two integrated dual-band downtilt omni-directional antennas for 2x2 MIMO with peak antenna gain of 4.9dBi in 2.4GHz and 5.7dBi in 5GHz.Worst-case internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 0.7dB in 2.4GHz and 1.3dB in 5GHz. Two (female) RP-SMA connectors for external dual band antennas (A0 and A1, corresponding with radio chains 0 and 1).802.11mc Fine Timing Measurement (FTM):.For total (EIRP) transmit power, add antenna gain. ![]() Note: conducted transmit power levels exclude antenna gain.2.4 GHz band: +21 dBm (18dBm per chain).Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):.Transmit power: Configurable in increments of 0.5 dBm.802.11n/ac packet aggregation: A-MPDU, A-MSDU.802.11ac very high throughput (VHT) support: VHT20/40/80.802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units.802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM).802.11b: Direct-sequence spread-spectrum (DSSS).Available channels: Dependent on configured regulatory domain.Supported frequency bands (country-specific restrictions apply):.Maximum number of BSSIDs: 16 BSSIDs per radio.Maximum number of associated client devices: Up to 256 associated client devices per radio.2.4GHz radio: Two spatial stream Single User (SU) MIMO for up to 574Mbps wireless data rate with individual 2SS HE40 802.11ax client devices or with two 1SS HE40 802.11ax MU-MIMO capable client devices simultaneously.5GHz radio: Two spatial stream Single User (SU) MIMO for up to 1.2Gbps wireless data rate with individual 2SS HE80 802.11ax client devices, or with two 1SS HE80 802.11ax MU-MIMO capable client devices simultaneously.AP type: Indoor, dual radio, 5GHz and 2.4GHz 802.11ax 2x2 MIMO.HPE FlexFabric and FlexNetwork Switches. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |